Type: Driver
File Name:
File Size: 30.7 MB
6 (3.12)
Downloads: 4
Supported systems: Windows 10, 8.1, 8, 7, 2008, Vista, 2003, XP, Other
Price: Free* (*Free Registration Required)

Download Now

Windows is a registered trademark of Microsoft Corporation. This document contains proprietary information of Continental Access. Unauthorized reproduction of any portion of this manual without the written authorization Lantronix DeviceInstaller Continental Access is prohibited. The information in this manual is for informational purposes only. It is subject to change without notice. Companies, names and data used in examples herein Lantronix DeviceInstaller fictitious unless otherwise noted. Continental assumes no responsibility for incorrect information this manual may contain.


The Xport plugs directly into Continental Access controllers. The Lantronix DeviceInstaller for Super2 controllers and accelerator boards are referred to as a network interface board. This information must be supplied to you by the network administrator. If this address changes in the future, the CardAccess software will not communicate to the panel.

Where can I download the Lantronix DeviceInstaller for W7, W8, or W10?

It is highly recommended to use a static IP address. This cable can be used to program the Lantronix using hyperterminal. Using hyperterminal is an alternate method to Lantronix DeviceInstaller DeviceInstaller. Using a crossover cable eliminates any switches or hubs from blocking the device.

Acer Aspire V3-771 Realtek HD AudioWhat is the latest version of DeviceInstaller?
Biostar GeForce 8400GSYour Answer

It is not recommended to cut the serial cable supplied with Lantronix DeviceInstaller external Lantronix device. This serial cable is for configuring the Lantronix device only.


The gauge of the wire doesn t meet the Continental Access wiring specifications. Below is the wiring diagram for the Lantronix cable.

Lantronix device installer download

Lantronix 25 pin Panel polling connector txd rxd gnd 2 5 Scope This document contains information regarding the installation and the configuration of the Lantronix DeviceInstaller. DeviceInstaller is an all-in-one utility that gives you the ability to configure a Lantronix device using different methods. The two methods are telnet and Lantronix DeviceInstaller.

Lantronix DeviceInstaller document will focus on using the telnet method. Using the telnet feature of DeviceInstaller is very similar to using hyperterminal and a serial cable on external Lantronix devices. In addition to this document, you may refer to the DeviceInstaller user guide on the Lantronix website. The following information might be slightly different compared to the website. To download, you will be prompted to download via ftp or http.

Download the utility to your hard drive. The Lantronix DeviceInstaller you download should be or higher. Installing DeviceInstaller Once the DeviceInstaller is downloaded to your hard drive, you must install it. Double click the file you downloaded and follow the prompts to install. The program will install a shortcut in the start menu under Lantronix. Verify the Lantronix DeviceInstaller program opens refer to figure 1. If you are prompted to check for updates on the product information base, click NO. DeviceInstaller will display all Lantronix devices detected on the network. Devices that do not have an IP address assigned or are configured on a different network, display in red. You must assign an IP address to the device Lantronix DeviceInstaller use it. If DeviceInstaller fails to detect your Lantronix device, refer to Appendix B for troubleshooting tips.

Click and expand Local Area Connection. UDS and XPort should display. Verify the device you are configuring displays on the right side of the screen. You can identify your device by the hardware address. The hardware address is also called the MAC address. All network devices have a unique MAC address. XPorts have the MAC address written on the outside.

Scripting must be enabled to use this site.

If this occurs, the IP address Lantronix DeviceInstaller from the DHCP server along with the hardware address will display on the right side of the screen. If the current Lantronix DeviceInstaller address is incorrect, you can manually assign the correct IP address. After verifying the hardware address, click the correct Lantronix device on the right side of the screen.

The Lantronix DeviceInstaller is a Windows-based GUI Lantronix DeviceInstaller that provides an easy way to install and configure specific Lantronix device server products. Lantronix Device Installer Software Firmware Updates.


Lantronix Device Installer. Version: Date:4/23/

Related Drivers